Fitting A Cat Flap In A UPVC Door
The ability of your cat to come and go from the house at its own pace is a good idea to keep it physically and mentally active. Having a flap can also help reduce toileting accidents by making it easier for your cat to leave the house when it needs to.
Measure the Door
A cat flap allows your pet to come and go whenever they'd like without needing to open the door. This makes it ideal to keep them in the house when you're at home or away, and helps keep unwanted pests out of your house as well!
It's important to measure the door prior to when you buy a cat flap as there are a variety of sizes available. This will ensure that you purchase the right size to fit inside your door made of upvc, otherwise, it could be too small or large for your cat and he will be unable to use it.
Take a ruler, and measure the width at several locations along the edge of the door. You should also take measurements of the height of the door in fitting a Cat flap in a upvc door few places. A door that is too tall can cause your cat to perform a gymnast routine every time it is tempted to use the flap.
If you're not sure how much to install a cat flap to measure the door, it could be best to ask for assistance from a glazier, or someone who is familiar with this type of work often. They will be able to assist you in determining whether not your door is suitable for a cat flap, and help you decide on the best size of flap you should purchase.
Once you've got your measurements, the next thing to do is to draw the shape of the hole in the door. This will give you a guide when it comes to cutting the hole out and will help you avoid making a mistake that could cost you money in the long run!
Make sure that you put the hole in the correct location. For instance, if installing the cat flap inside the patio door, it's important that the hole doesn't sit too close to hinges, as this could cause leakage and damage to the seal.
It is recommended to leave the job of installing the cat flap onto glass doors to a professional glazier. It can be fitting a cat flap challenge to fit a cat flap into the glass pane and you could discover that the process causes it to break and lose its weatherproof seal.
Measure the Cat
A cat flap lets your pet leave and come back whenever they want without you needing to leave him on his own. It can also stop the draughts from entering your home, which isn't bad for you or your cat!
However, if you own a uPVC or composite door it may be difficult to install the cat flap fitting near me flap. These doors are constructed of different materials and the process of installing them is different. Make sure to inquire with the manufacturer to see if it is compatible before you install the cat flap on your uPVC composite or uPVC door. Modifications can cause warranty issues.
Generally speaking, these kinds of doors are built to be tough and durable with insulation included. They are more resistant to the weather than other types of doors, however it isn't easy to install a cat flap. Get advice from a professional before installing a cat flap onto a uPVC door or composite.
You'll have to measure the height of your child to ensure that they can fit through the door. This will be easiest if they are asleep or calm so that they don't move around too often. Once you have their height, you can measure the distance between their stomachs and the floor in order to determine the location of the flap's bottom. This position can be marked on the door.
If you are using power tools to cut your uPVC or composite door, you need be cautious. The process of drilling into metal could cause cracks, particularly in the case of toughened glass. It is highly recommended to employ a glass installer when installing a cat flap in a pane. This will prevent the glass from becoming fragile or shattering. A Glazier will also be in a position to provide you with a circular cat flap hole that is less likely to break and is safer for your double glazing cat flap to use.
Cut the Hole
A good quality cat flap will come with a template that you can use to mark the area on your door where the hole will be. If it doesn't, you could make your own using a thin sheet of paper (tracing papers are great). Once the shape has been drawn in pencil on the door, then use a spirit level to make sure that the shape is completely horizontal. This will ensure that your cat flap is properly positioned in the door, and it will not open or close.
Then, you can use your jigsaw, and cut the shape that has been written on the door. Use a blade designed for uPVC doors. It will usually be identified with this information. If not then ask the staff at your DIY store for assistance. Once the hole is cut then place the flap against it and open it to make sure the flap is moving smoothly. If it is bound at any point, use a filer or a rasp to remove it.
Also, make sure that there are no electric gas or cable lines within the door that you will be cutting through, since they could be damaged by your jigsaw. Be aware of any handles, or other fixtures in the door, which have to be removed to fit the cat flap. Be careful not to scratch these objects during the process.
Most people who install a cat flap themselves will have an ordinary solid uPVC door, and therefore will not be dealing with any of these problems. If your door is constructed of wood or has an ornamental panel that can't be removed then this will make it more difficult to complete the task.
It is always advisable to seek assistance from an expert cat flap fitter for these kind of jobs since it is essential to do the job done correctly to avoid potential problems in the future. It is important to get it right, as getting it wrong could damage the door and void the warranty.
Place the Flap
After you've cut your hole, put the flap to see whether it opens and fits. If you find any points that stick or catch to the wall, use a hand file or sandpaper to file them down until they fit perfectly and can be opened without issue. Make sure the flap is in line with the door.
If your kit doesn't include an example, you could use thin paper like tracing or acetate. Place the paper on the door and draw a line where you need to position the flap (this will be your cutting guide). Mark four screw holes at every corner of the flap using the pencil marks you traced on the door. These will be the screw holes you'll need to fix the flap in place.
The majority of upvc door panel replacement cat flap doors are strong and therefore easy to cut into. If the door is made of composite or GRP however, it could be more difficult. If you're not comfortable with this, it is best to hire a professional. They can also help you determine whether or not your specific door is suitable for cat flap installation.
It is possible to install an opening for a cat flap in composite doors. However, it's essential to consult with the manufacturer or a professional joiner before you do so because any changes to these types of doors could invalidate the warranty. If you decide to tackle the work yourself, bear in mind that it could be messy and even dangerous.
You'll need a saw or grinder to cut through composite doors, rather than just the GRP. Be aware that this could be a very hazardous job and you'll have to take extreme care not to harm the door or yourself as it is very fragile. It's important to remember that cutting a hole into any type of glass for a door is a lot more difficult than making the same change in a uPVC or solid timber door.