24-Hours To Improve Fiat Panda Key Fob Replacement

Reasons Your fiat grande punto key 500 Key Fob Won't Work

A fiat 500 key cutting ducato Key Programming; wifidb.Science, 500 key fob makes it simple to open doors and start your car. There are many reasons the fob won't work. This includes a dead coin-battery, water damage, receiver modules issues, and interference.

This listing is for an NEW replacement fiat 500 key cover uk Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob will not work is an inactive battery. Modern key fobs come with a limited operating range, and should be within only a few feet from the vehicle to function. If you're far from your car and press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) with a brand new one from a reliable brand such as Panasonic, Duracell, or Energizer. You can usually find them in your local hardware store or online.

You can test the battery in the coin-cell by pressing the buttons while you're standing close to your Fiat 500. The parking lights will flash and the key fob should operate the lock and unlock switch.

If the fob's key doesn't work after replacing the battery, it may be damaged by water that blocks it from connecting to the receiver module in your vehicle. Water damage can occur in a variety of ways, ranging from the slightest splash to submerging the fob into salt water at the beach. If you believe your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this doesn't work, you will have to get your fob changed by an auto locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater is especially dangerous to the circuit board of the fob and can cause it to short out and eventually die. It's not a good idea to soak the fob in water however, but don't give it up in the event that you accidentally drop it in water, or fail to remove it from your pants pocket.

First remove the battery from the fob. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Test the fob next to determine if it's working. If the fob doesn't work, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is older and is not programmed to work with your vehicle, you will need to replace it completely. A professional locksmith for automotive can do this job. The locksmith must cut the key to match the ignition of your vehicle. The locksmith will also need to program your fob into the vehicle's system. This is a simple and cost-effective process that can usually be completed the next day.

Receiver Module Issues

One of the main reasons your 500 key fob may stop working is because it's out of range. The remote has a maximum range of 30 feet, which means when you're too far from your vehicle it will not respond to your commands. This can be fixed by moving it closer to your vehicle until it begins responding.

If your fob does not work after you replace the battery inside the coin, which is also known as a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. In the majority of cases, reprogramming your fob can resolve the issue. You can find the instructions on how to do this on the majority of vehicles by searching YouTube or checking out the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, it can prevent the battery from sitting properly, and this will cause your remote to malfunction.

In rare cases the fob could be out of connection with your vehicle as a result of hardware or software issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases it is possible that the software will require reinstallation into your body control modules.

Interference

In addition to a dead battery on a coin, the key fob may not be able to transmit or receive the signal due to interference. This could occur if the keyfob's location is in close proximity to a radio transmitter, like a cell phone or radar detector. Other reasons the key fob could not function may be a lack of connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a defective receiver module on your 500. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then read by the vehicle.

There's a quick and easy way to reset the 500's in-board system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then reconnect the battery. This will remove any remaining electricity and restart the car's computer system, which can help get your key fob working again. If the problem persists it is recommended that you consult an experienced technician. They'll be able determine the root of your problems.